Front Sachs
- Thread starter danterzza
- Start date
photo_ed
ClioTrophy Club Member
- Joined
- Jul 22, 2018
- Messages
- 1,392
- Reaction score
- 2,462
- Location
- Yorkshire/Lancashire
- Trophy No.
- 407
Hi,
Very interested in these. I've sent a PM.
?
Very interested in these. I've sent a PM.
?
Yeah nice quick sale there.
I've always thought your almost better buying a cheaper set knowing they need a refurb than an expensive set that are hiding needing one. Plus you don't have to stress about them getting posted to you.
I've always thought your almost better buying a cheaper set knowing they need a refurb than an expensive set that are hiding needing one. Plus you don't have to stress about them getting posted to you.
photo_ed
ClioTrophy Club Member
- Joined
- Jul 22, 2018
- Messages
- 1,392
- Reaction score
- 2,462
- Location
- Yorkshire/Lancashire
- Trophy No.
- 407
Indeed. Having sadly missed out on the group buy of the remaining new sets a while back, I thought it prudent to have a spare set 'in stock' as it were, to have refurbed at my leisure and thus always have Sachs on the car rather than the rigmarole of having to put Cup shocks on and off when it comes to refurb time. ??
Ideal if you also have a spare set of springs and spring hats / top mounts. A breeze with just the strut top cap under the bonnet and the 2 bolts to the hub, providing the top cap isn't too tight!
photo_ed
ClioTrophy Club Member
- Joined
- Jul 22, 2018
- Messages
- 1,392
- Reaction score
- 2,462
- Location
- Yorkshire/Lancashire
- Trophy No.
- 407
... and arrived.
Many thanks Dan for sorting & the super quick postage too. A real pleasure to do business. Appreciated. ? ☺
photo_ed
ClioTrophy Club Member
- Joined
- Jul 22, 2018
- Messages
- 1,392
- Reaction score
- 2,462
- Location
- Yorkshire/Lancashire
- Trophy No.
- 407
I have do a spare set of original springs, so cheers for the idea of building up the whole unit to simply bolt on and off, I hadn't actually thought that far ahead, but it certainly makes sense! ?
If they look like the ones above, they will need a refurb. No real hard and fast rules and short of them being put on a test jig there is no well to tell how healthy they are. Generally if you can push down the front corner of the car they have failed, it should be absolutely solid. The same can be said of any that are not fitted to a car. The only tell tale sign that they are probably on their way out will be the appearance of oil and sometimes the remote reservoir will have risen and be touching or very close to the ”arm” that attaches it the the main body of the damper and it may actually wiggle around.
they don't look like the ones above, they looks like in good stat without rust.....
there is no oil leak but on the right side, when i apply pressure on wing an release, the clio bounce
it was detected during a technical control since few days......
is it possible of a lower gaz pressure only?
if yes is it possible to increase easily this pressure?
there is no oil leak but on the right side, when i apply pressure on wing an release, the clio bounce
it was detected during a technical control since few days......
is it possible of a lower gaz pressure only?
if yes is it possible to increase easily this pressure?
When I said “like the ones above” I meant that the fact the the rods were retracted into the body meant that they needed a refurb, in good order they are always extended.
If you are able to easily bounce a front corner, the damper has failed in some way. Rik would be a better person to answer this but my guess is that the gas pressure has gone, as you say. Does the reservoir touch the horizontal part? There was a discussion a while back as to whether we can re pressurise but if it has lost pressure then a seal has probably failed and it will just lose the gas again.
If you are able to easily bounce a front corner, the damper has failed in some way. Rik would be a better person to answer this but my guess is that the gas pressure has gone, as you say. Does the reservoir touch the horizontal part? There was a discussion a while back as to whether we can re pressurise but if it has lost pressure then a seal has probably failed and it will just lose the gas again.
ok i understand that the rods have to be always extended to be ok .
i have to check the position of the reservoir but during the technical control done few days ago i didn't see any anormal position.
what is the horizontal parts you mean?
i have to check the position of the reservoir but during the technical control done few days ago i didn't see any anormal position.
what is the horizontal parts you mean?
I’m not totally confident offering advice on this as I’m not the expert, but yes I could move the reservoir ever so slightly by hand on the failed one. There was no sign of any oil leak and had lost pressure, in the end the whole shaft was replaced despite looking perfect
The second good damper was fine with no movement but I wouldn’t get too hung up on that as I have another pair that have both failed and neither remote on those moves.
As to the technical specs, I doubt any of the specialists will release that information.
As to the technical specs, I doubt any of the specialists will release that information.